RCBS (15)

This collet is designed be used with the RCBS(R) Standard Bullet puller to remove bullets.Features : For use with RCBS Standard Bullet puller Collet

Walnut shell media is the fastest way to clean and shine your brass in a dry tumbler. RCBS Formula 1 walnut shell media is ground to 12/12 sieve size, and treated with case polishing additives - perfect for cleaning your brass quickly to like-new condition!Features : Treated with case polishing additives Walnut shell media

The 3-Die Roll Crimp Set is for loading straight-wall cartridges. Its steel Sizer Die sizes the case and de-primes. Note: Cases must be lubricated. The Expander Die expands the case to the proper diameter to accept the bullet, and it imparts case mouth flare/bell for bullet feeding. The Seater Die seats the bullet and roll crimps.Features : Steel Sizer Die Expander Die Seater Die

This two-die set is for bottleneck cases to be fired in bolt-action rifles only-specifically, cases fired out of a specific rifle and neck-sized to go back into the same rifle. The set consists of a Neck Sizer Die with an Expander-Decapping Unit, and a Seater Die with Bullet Seater Plug. The Neck Sizer Die resizes the neck only (it doesnt touch the shoulder or body) and de-primes. The included Seater Die has a built-in roll crimper to secure the bullet at the same time its seated.Features : Neck Sizer Die with an Expander-Decapping Unit Seater Die with Bullet Seater Plug

The RCBS(R) Case Lube Pad is the best way to lubricate cases for resizing or forming. Coat the pad with Case Lube-2" then roll the case lightly across it. Exactly the right amount of lubricant is transferred to the case. The pad can be removed from the sealable storage case for easy cleaning.Features : Pad can be removed from the sealable storage case for easy cleaning Case lube pad

The RCBS(R) Quick Change Powder Measure can quickly go from light pistol to magnum rifle charges. The hopper holds 1 pound of smokeless powder. The unit features metering assemblies that change out with the pull of a pin. Extra metering assemblies can be purchased to have them preset for favorite smokeless powder charges. The drain attachment empties the powder hopper without the need to remove it from the stand or press. Note: The Powder Measure should be used in conjunction with an accurate powder scale for setting the original charge and for checking charges occasionally during the run.Features : Includes a drain attachment and small and large metering assemblies Allows reloaders to quickly convert from light pistol to magnum rifle charges

RCBS(R) offers a variety of decapping pins for all reloading needs.Features : 50-Pack Decapping pins

Properly clean and lube cases for resizing the simple way with this complete kit. It includes the RCBS(R) Case Lube Pad, a 2-ounce bottle of Case Lube-2 and two interchangeable Case Neck Brushes for 22 through 30 caliber.Features : Case lube pad Case lube Case neck brushes

With the RCBS(R) Shell Holder Rack, reloaders can keep shell holders organized and protected. The Shell Holder Rack has 12 positions that hold two shell holders on each post. There is also room to store six Trim Pro(R) Shell Holders as well. The clear cover keeps out the dust and dirt while allowing reloaders to see what is stored in the rack. The Shell Holder Rack can be mounted on the wall or used on the bench. The wall mount spacing allows it to be hung off of standard 1-inch pegboard hooks as well. The support legs angle the bottom out for wall mounting or the top up for bench use. Additional Shell Holder Racks can be snapped together if more shell holder storage is needed.Features : 12 Positions hold two shell holders on each post Clear cover keeps out dust and dirt Can be hung off of standard 1-inch pegboard hooks

This collet is designed be used with the RCBS(R) Standard Bullet puller to remove bullets.Features : For use with RCBS Standard Bullet puller Collet

This two-die set is intended for reloading bottleneck cases, and consists of a Full-Length Sizer Die with an Expander-Decapping Unit, and a Seater Die with Bullet Seater Plug. The Full-Length Sizer Die brings the case to SAAMI minimum cartridge dimensions. It sizes the outside of the case, de-primes and expands the neck to accept the bullet. The die has vents to prevent case damage caused by trapped air and for excessive lubricant. Headspace is held to minimum tolerances to avoid changing the case body length during full length sizing. The included Seater Die has a built-in roll crimper to secure the bullet at the same time as its seated.Features : Full-Length Sizer Die Seater Die with Bullet Seater Plug

This collet is designed be used with the RCBS(R) Standard Bullet puller to remove bullets.Features : For use with RCBS Standard Bullet puller Collet

This two-die set is intended for reloading bottleneck cases, and consists of a Full-Length Sizer Die with an Expander-Decapping Unit, and a Seater Die with Bullet Seater Plug. The Full-Length Sizer Die brings the case to SAAMI minimum cartridge dimensions. It sizes the outside of the case, de-primes and expands the neck to accept the bullet. The die has vents to prevent case damage caused by trapped air and for excessive lubricant. Headspace is held to minimum tolerances to avoid changing the case body length during full length sizing. The included Seater Die has a built-in roll crimper to secure the bullet at the same time as its seated.Features : Full-Length Sizer Die Seater Die with Bullet Seater Plug

This two-die set is intended for reloading bottleneck cases, and consists of a Full-Length Sizer Die with an Expander-Decapping Unit, and a Seater Die with Bullet Seater Plug. The Full-Length Sizer Die brings the case to SAAMI minimum cartridge dimensions. It sizes the outside of the case, de-primes and expands the neck to accept the bullet. The die has vents to prevent case damage caused by trapped air and for excessive lubricant. Headspace is held to minimum tolerances to avoid changing the case body length during full length sizing. The included Seater Die has a built-in roll crimper to secure the bullet at the same time as its seated.Features : Full-Length Sizer Die Seater Die with Bullet Seater Plug

This two-die set is for bottleneck type cases used in tight-chambering semi-automatic, pump or lever-action rifles. It consists of a Small Base Sizer with an Expander-Decapping Unit and Regular Seater Die with Seater Plug. The sizer resizes cases below SAAMI minimums, reducing the shoulder and body by a few thousandths. It also de-primes the case. The included Seater Die has a built-in roll crimper to secure the bullet at the same time its seated. To seat bullets without crimping, simply unscrew the die until the crimp ring no longer engages the case mouth.Features : Small Base Sizer with an Expander-Decapping Unit Regular Seater Die with Seater Plug